Skip to main content
Redmoon Converters
🌱

By ·

Setting Up an Indoor Seed-Starting Station: Light Height, Hours, Feed and Running Cost

Seedlings need the right light height, hours of light per day, a gentle nutrient dose and a power budget. One worked seed-starting rack shows how the numbers fit together.

GardeningGrow Lights

The usual seed-starting failure isn’t germination. Seeds come up fine. Then they grow tall and thin, reach for the window, fall over, or sit pale and stalled for weeks. That’s almost always a setup problem, not bad seed. Light height, how many hours the light is on, how strong the feed is, and how long it all runs are four separate settings, and the advice on a seed packet covers none of them.

This guide sets up one seed-starting rack from scratch and puts a number on each of those four settings. The underlying physics and chemistry already have their own posts on this site, linked below. This one is about how the pieces fit together.

The rack

The example is a two-shelf wire rack in a cool basement, the kind of setup many gardeners put together in late winter for tomatoes, peppers, brassicas and flowers:

  • Two shelves, each holding two standard 10 × 20 in trays
  • Two 2-ft full-spectrum LED fixtures per shelf, 22 W each, so four fixtures and 88 W in total
  • The fixture maker lists 300 µmol/m²/s at 12 inches below the center of the light
  • One 20 W seedling heat mat, used only for germination
  • A liquid 9-3-6 concentrate, density about 1.2 g/mL, with a label rate of 5 mL per gallon for established plants

If your fixture’s box doesn’t give a PPFD figure, and many cheap shop lights don’t, you can estimate one from a lux reading. The grow-light guide explains why lux needs a spectrum correction and roughly how big that correction is. Treat any figure you get that way as approximate.

Step 1: Set the height for intensity

The Grow Light Distance Calculator takes the fixture’s rated PPFD and reference distance, the distance you actually plan to hang it, and a growth stage. Its seedling band is 200–400 PPFD. The guide linked above explains the inverse-square relationship behind it, and here’s what it gives for this fixture:

Light-to-leaf distancePPFD at canopyTool verdict (Seedling)
8 in675Too bright, move to ~12 in
12 in300In range
13.5 in237In range
14.5 in205In range, at the low edge

The common advice to “hang it a couple of inches above the seedlings” assumes old fluorescent tubes, which were far weaker. A modern LED that close would be well outside the band, and the inverse-square figure stops being reliable when you’re that near a wide fixture. With this light, anywhere from about 12 to 14 inches is in range. The next step decides where in that range to hang it.

Measure from the top of the leaves, not the top of the tray. Seedlings grow fast, so check the height every few days. A chain or ratchet hanger makes raising the light quick. A cheaper option is to lower the trays onto upturned pots.

Step 2: Choose the hours and check the total light

PPFD is a rate: how much light lands on the leaves each second. What a plant actually grows on is the total amount it gets over the day. Growers call that the daily light integral (DLI), measured in moles of light per square metre per day:

DLI (mol/m²/day) = PPFD × hours of light × 0.0036

The 0.0036 combines 3,600 seconds per hour with the conversion from micromoles to moles. The Grow Light Distance Calculator does not calculate DLI and doesn’t ask for a photoperiod. You’ll need to work this part out yourself, but it’s one line of arithmetic.

What DLI should seedlings get? Research on greenhouse bedding plants generally puts good-quality seedlings at around 10–12 mol/m²/day. Many growers run vegetable seedlings anywhere from about 8 up to the mid-teens. This rack aims for about 12. Hours and PPFD trade off against each other, so there’s more than one way to get there:

OptionPPFDHours onDLI
Hang at 12 in, run 16 h3001617.3
Hang at 12 in, run 14 h3001415.1
Hang at 13.5 in, run 14 h2371412.0
Hang at 14.5 in, run 16 h2051611.8

Every row is “in range” in the calculator, but the first gives 45% more light per day than the last. Use the distance tool to stay inside the intensity band. Use hours and DLI to set the daily total.

Two rules for the timer. Use one, because a light that someone forgets to turn off is the most common way a schedule goes wrong. And don’t run the lights 24 hours a day to make up for a weak fixture. Some crops, tomatoes among them, get leaf damage under continuous light. A daily dark period of at least 8 hours is the usual advice, so 14–16 hours on is the normal range.

This rack runs at 13.5 inches for 14 hours. That gives plenty of light without being harsh, and it leaves room to raise the light as the plants grow.

Step 3: Hold off on feeding, then feed gently

Most seed-starting mixes contain little or no fertilizer, and the seed itself feeds the seedling until its first true leaves open. Feeding before that mostly feeds algae on the surface of the mix. When the first true leaves have opened, start with a dilute feed and raise the strength as the plants grow.

The fertilizer guide covers how a label’s NPK turns into ppm, including the oxide conversion, the density step and the EC meter scales. For this 9-3-6 concentrate in the Fertilizer / Nutrient Dilution Calculator, here’s what different doses work out to:

Dose per US gallonNitrogenEstimated EC (mS/cm)Use
1.25 mL (quarter rate)~36 ppm N0.28First true leaves
2.5 mL (half rate)~71 ppm N0.56Two to four true leaves
3.09 mL (“Seedling” preset)~88 ppm N0.69Sturdy seedlings before transplant
5 mL (label rate)~143 ppm N1.12Potted-up plants growing on

The Seedling preset button is useful. It works backward from 150 ppm total dissolved N + P + K and sets the dose to match your fertilizer, which for this concentrate is 3.09 mL per gallon. A common rule for seedlings is to start around 50 ppm nitrogen and work up toward 100. Half rate followed by the preset fits that well, and the full label rate is for later.

One caution about the EC column. EC is what the meter measures, and it’s the same number whichever ppm scale your meter displays. On a 500-scale meter the preset dose reads about 346 ppm, and on a 700-scale meter about 485, for the same water. The calculator estimates EC from the dissolved nitrogen, phosphorus and potassium, scaled by a complete reference feed that also carries calcium, magnesium and sulphur. A simple N-P-K concentrate can read lower than that, and your tap water’s own minerals add to whatever the fertilizer contributes. Measure your plain tap water first, then measure the mixed solution, and track the difference between the two from week to week. Use the calculator to find the dose, and the meter to check what’s actually in the water.

Step 4: Price the season

Power is the cost people forget, and the Appliance Electricity Cost Calculator covers it. Lights draw close to their rated wattage whenever they’re on, so you can enter the hours directly. There’s no duty cycle to estimate. At an example rate of $0.17/kWh:

ItemEnteredPer daySeason
Four LED fixtures88 W × 14 h1.23 kWh, $0.2156 days ≈ $11.73
Heat mat, germination only20 W × 24 h0.48 kWh, $0.0814 days ≈ $1.14

So eight weeks of seedlings costs about $13 in electricity at this rate. The tool shows cost per day, week, month and year. It doesn’t take a number of days, so for an eight-week season multiply the daily figure by 56 yourself. If you ran the 16-hour schedule from the first row of the DLI table instead, the lighting would cost about $13.40 for the same season. It’s not much money, but it’s a reason not to run more hours than the plants need.

The heat mat’s 24-hour figure is a worst case. A mat on a thermostat cycles off once the tray is warm, so the real cost will be lower. As with any electrical setup near water: plug everything into a GFCI-protected outlet, keep connections above the drip line, and don’t put a heat mat under a tray that leaks onto it.

How the four settings interact

If you change one setting, check the others:

  • Raising the light for taller seedlings lowers PPFD, so check whether the hours still give you the DLI you want.
  • Adding hours to make up for a weak light raises the electricity cost in a straight line and reduces the dark period.
  • More light means more growth, and plants that grow faster use nutrients faster. A rack running at DLI 17 may want the stronger end of the feed table sooner than one at DLI 12.
  • Stretched, pale seedlings usually need more light per day, not more fertilizer. Fix the light first.

This is general growing guidance. Crops and varieties differ. Check the specific needs of what you’re growing, and follow the fertilizer label’s safety directions.

Set up your own rack

Put your fixture’s rated PPFD into the Grow Light Distance Calculator to find the height range for the seedling band, then pick the hours that give the DLI you want. Choose a dose for your concentrate in the Fertilizer / Nutrient Dilution Calculator, starting low. Then enter the rack’s total wattage and hours into the Appliance Electricity Cost Calculator so you know the running cost before the season starts.

Try the tools from this guide